Cisco CCNA WIRELESS IUWNE Training

Cisco Certified Network Associate Wireless (CCNA Wireless) validates associate-level knowledge and skills to configure, implement and support of wireless LANs, specifically those networks using Cisco equipment. With a CCNA Wireless certification, network professionals can support a basic wireless network on a Cisco WLAN in a SMB to enterprise network. The CCNA Wireless curriculum includes information and practice activities to prepare them for configuring, monitoring and troubleshooting basic tasks of a Cisco WLAN in SMB and Enterprise networks.

Describe WLAN fundamentals

Describe basics of spread spectrum technology

Describe the impact of various wireless technologies (Bluetooth, WiMAX, ZigBee, and cordless phone)

Describe wireless regulatory bodies, standards and certifications (FCC, ETSI, 802.11a/b/g/n, and WiFi Alliance)

Describe Wireless LAN (WLAN) RF principles (antenna types, RF gain/loss, Effective Isotropic Radiated Power (EIRP), refraction, reflection, and so on)

Describe networking technologies used in wireless (SSID to WLAN_ID to Interface to VLAN, 802.1q trunking)

Describe wireless topologies, such as Independent Basic Service Set (IBSS), Basic Service Set (BSS), Extended Service Set (ESS), Point-to-Point, Point-to-Multipoint, Mesh, and bridging)

Describe 802.11 authentication and encryption methods (Open, Shared, 802.1X, EAP, TKIP, and AES)

Describe frame types (associated and unassociated, management, control, and data)

Describe basic RF deployment considerations related to site survey design of data or VoWLAN applications, common RF interference sources such as devices, building material, AP location, and basic RF site survey design related to channel reuse, signal strength, and cell overlap

Describe WLAN fundamentals

Identify the components of the Cisco Unified Wireless Network architecture (Split MAC, LWAPP, stand-alone AP vs controller-based AP, specific hardware examples)

Install and configure autonomous access points in the small business environment

Describe the modes of controller-based AP deployment (local, monitor, HREAP, sniffer, rogue detector, bridge, OEAP, and SE-Connect)

Describe controller-based AP discovery and association (DHCP, DNS, Master-Controller, Primary-Secondary-Tertiary, and n+1 redundancy)

Describe roaming (Layer 2 and Layer 3, intra-controller and inter-controller, and mobility list)

Configure a WLAN controller and access points WLC: ports, interfaces, WLANs, NTP, CLI and Web UI, CLI wizard, and link aggregation group (LAG) AP: Channel and Power

Describe Radio Resource Management (RRM) fundamentals including ED-RRM.

Verify basic wireless network operation

Install Wireless Clients

Describe client WLAN configuration requirements, such as Service Set Identifier (SSID), security selection, and authentication

Identify basic configuration of common wireless supplicants (Macintosh, Intel Wireless Pro, Windows, iOS, and Android)

Describe basic AnyConnect 3.0 or above wireless configuration parameters

Identify capabilities available in CCX versions 1 through 5.

Implement basic WLAN Security

Describe the general framework of wireless security and security components (authentication, encryption, MFP, and IPS)

Describe the evolution of supported authentication methods (PSK, 802.1X including EAP-TLS, EAP-FAST, PEAP, LEAP, and WPA/WPA2)

Configure the different sources of authentication (EAP-local or -external, and Radius)

Configure authentication and encryption methods on a WLAN (WPA/WPA2 with PSK and 802.1x)

Implement wireless Guest networking

Operate basic WCS

Identify key functions of Cisco Wireless Control System (WCS) and Navigator (versions and licensing)

Navigate WCS interface

Configure controllers and access points (APs) (using the Configuration tab not templates)

Use preconfigured maps in the WCS (adding/relocating/removing access points, turn on/off heat maps, view client location, and view CleanAir zones of influence)

Use the WCS monitor tab and alarm summary to verify the WLAN operations

Generate standard WCS reports (inventory, CleanAir, client-related, AP-related, and utilization)

Conduct basic WLAN Maintenance and Troubleshooting

Identify and use basic WLAN troubleshooting tools (WLC show debug and logging) for client to AP connectivity, AP to controller connectivity

Use the WCS client troubleshooting tool

Transfer logs, configuration files, and O/S images to and from the WLC via the GUI

Differentiate and use WLC and AP (autonomous and LAP) management access methods (console port, CLI, telnet, ssh, http, https, and wired vs wireless management)

 

 

 

TAGS: CCNA Wireless IUWNE Training Mumbai, CCNA Wireless IUWNE Training Institute Mumbai, CCNA Wireless IUWNE Classes, Cisco CCNA Wireless IUWNE Course In Mumbai, Navi Mumbai , Thane, Pune, India

"NETTECH IS THE BEST TRAINING PROVIDER FOR CCNA, CCNP, CCIE, MCSA, MCITP, RHCE, ETHICAL HACKING, VMWARE IN THANE WITH CERTIFIED PROFESSIONAL."
Nettech India

Contact us

If you want more information fill in this form. You will be contacted as soon as possible. Please fill in all required fields.

Name*
Email*
Mobile*
Message*
Send a copy to my own email address


CAREER PACKAGES